View 5520_8829449.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

street fire ? www.street-fire.com ? (915) 857-5200 ? fax (915) 857-3344 parts included: 1 - ignition 1 - harness, pn 8860 warning: during installation, disconnect the battery cables. when disconnecting the battery always remove the negative cable frst and install it last. note: solid core spark plug wires cannot be used with the street fire ignition. note: the street fire ignition cannot be used with distributorless ignition systems (dis). ge neral information battery the street fire ignition control will operate on any negative ground, 12 volt electrical system with a distributor. it can be used with 16 volt batteries and can withstand a momentary 24 volts in case of jump starts. the ignitions will deliver full voltage with a supply of 9 - 18 volts and will operate with a supply voltage as low as 7 volts. coils the street fire ignition can be used with most stock coils and aftermarket coils designed to replace the stock coils. if you have any questions concerning coils, contact our customer service department at (915) 855-7123. tachometers the street fire ignition features a tach output wire that provides a trigger signal for tachometers, a shift light or other add-on rpm activated devices. the tach output produces a 12 volt square wave signal with a 24% duty cycle. some vehicles with factory tachometers may require a tach adapter to operate with the ignition. for more information on tachometers and msd tach adapters, see the tachometer section on page 9. if your gm vehicle has an inline flter it may cause the tach to drop to zero on acceleration. if this occurs, bypass the flter. foreign vehicles due to the fuel injection systems, some foreign vehicles may require a special tach/fuel injection adapter with a street fire ignition. see page 9 for wiring and tach adapter information. note: vehicles originally equipped with a cd ignition control cannot use the street fire ignition. spark plugs and wires spark plug wires are very important to the operation of your ignition system. a good quality, helically wound wire and proper routing are required to get the best performance from your ignition, such as the street fire wire. note: solid core spark plug wires cannot be used with the street fire ignition. spark plugs : choosing the correct spark plug design and heat range is important when trying to get the best performance possible. it is recommended to follow the engine builder or manufacturer's specifcation for spark plugs. with that, you can then experiment with the plug gap to obtain the best performance. the gap of the plugs can be opened in 0.005" increments, then tested until the best performance is obtained. miscellaneous information sealing: do not attempt to seal the ignition. all of the circuits of the street fire ignition receive a thick conformal coating of humi-seal. rubber plugs are supplied to protect the rpm dials. welding: if you are welding on your vehicle, to avoid the chance of damage, always disconnect both heavy power cables of the ignition (you should also disconnect the tach ground wire). 1 - 18" ground wire 1 - 100v/1a diode 4 - mounting screws street fire cdi pn 5520 online product registration: register your msd product online. registering your product will help if there is ever a warranty issue with your product and helps the msd r&d team create new products that you ask for! go to www.msdperformance.com/registration.
2 installation instructions mounting the street fire ignition can be mounted in most positions, except directly upside down (if upside down, moisture or water cannot escape). it can be mounted in the engine compartment as long as it is away from direct engine heat sources. it is not recommended to mount the unit in an enclosed area such as the glove box. when you fnd a suitable location to mount the unit, make sure the wires of the ignition reach their connections. hold the ignition in place and mark the location of the mounting holes. use an 1/8" drill bit to drill the holes. use the supplied self tapping screws to mount the box. cylinder select the rev limiter that is built into the ignition is programmed for operation on a 8-cylinder engine. if you are installing one of these units on a 4 or 6-cylinder even-fre engine, the cylinder count must be selected. this is easily achieved through the cylinder select wire loops on the side of the ignition. to program the unit cut the loops as shown in figure 1. led there is a diagnostic led next to the rpm dials. the led will blink with each trigger signal. it will appear on when the engine is running. if the input voltage drops below 9 volts it will fash at idle speed. for more codes, see page 10. wiring wire length: all of the wires of the ignition may be shortened as long as quality connectors are used or soldered in place. to lengthen the wires, use one size bigger gauge wire (10 gauge for the power leads and 16 gauge for the other wires) with the proper connections. grounds: a poor ground connection can cause many frustrating problems. when a wire is specifed to go to ground, it should be connected to the battery negative terminal, engine block or chassis. there should always be a ground strap between the engine and the chassis. always securely connect the ground wire to a clean, paint free metal surface. these are the two heavy gauge wires (14 gauge) and are responsible for getting direct battery voltage to the ignition. this wire connects directly to the battery positive (+) terminal or to a positive battery junction or the positive side of the starter solenoid. note: never connect to the alternator. this wire connects to a good ground, either at the battery negative (-) terminal or to the engine. connects to a switched 12 volt source. such as the ignition key or switch. connects to the positive (+) terminal of the coil. this is the only wire that makes electrical contact with the coil positive terminal. connects to the negative (-) terminal of the coil. this is the only wire that makes electrical contact with the coil negative terminal. tach output wire. connect to the tachometer or other rpm device. there are two circuits that can be used to trigger the street fire ignition; a points circuit (white wire) and a magnetic pickup circuit (violet and green wires). the two circuits will never be used together. this wire is used to connect to the points or electronic ignition amplifer output . these wires are routed together in one harness to form the magnetic pickup connector. the connector plugs directly into an msd distributor. it will also connect to factory magnetic pickups or other aftermarket pickups. the violet wire is positive (+) and the green is negative (-). when these wires are used, the white wire is not. power leads heavy red heavy black red orange black gray trigger wires white violet and green (magnetic pickup connector) wire functions figure 1 selecting the number of cylinders. cylinder select loops street fire ? www.street-fire.com ? (915) 857-5200 ? fax (915) 857-3344
installation instructions 3 ballast resistor: if your vehicle has a ballast resistor in line with the coil wiring, it is recommended to bypass it. routing wires the street fire wires should be routed away from direct heat sources such as exhaust manifolds and headers and any sharp edges. the trigger wires should be routed separate from the other wires and spark plug wires. it is best if they are routed along a ground plane such as the block or frewall which creates an electrical shield. the magnetic pickup wires should always be routed separately and should be twisted together to help reduce extraneous interference. rev limiter the street fire ignition features an adjustable rev limiter. this feature will protect your engine from overrev damge in the event of driveline failure or a missed gear. the rev limit is adjustable from 2,000 - 9,900 rpm in 100 rpm increments (figure 3). prestart check list ? the only wires connected to the coil terminals are the street fire orange to coil positive and black to coil negative. ? the small red wire of the cdi is connected to a switched 12 volt source. ? if running a 4 or 6-cylinder engine the cylinder select must be modifed. ? the power leads are connected directly to the battery positive and negative terminals. ? the battery is connected and fully charged if not using an alternator. ? the engine is equipped with at least one ground strap to the chassis. the chart in figure 2 shows the polarity of other common magnetic pickups. figure 2 common mag pickup wires. common mag pickup wires colors mag+ mag- msd distributor org/blk vio/blk msd crank trigger violet green ford orange violet accel 46/48000 series org/blk vio/blk accel 51/61000 series red black chrysler org/wht black mallory org/blk vio/blk street fire cdi violet green warning: the street fire cdi is a capacitive discharge ignition. high voltage is present at the coil primary terminals. do not touch the coil or connect test equipment to the terminals. coil gray to tach www. street-fire.com pn 5520 cd i m ulti-spa rk igniti o n ? white orange black small red magnetic pickup not used street fire systems installing to points/amplifer style ignition. note: on dual point setups, it is recommended to remove the trailing set of points. note: ballast resistor is not necessary. note: remove the coil terminal wires. the negative wire connects to the street fire white. the positive wire connects to the street fire red. the street fire orange connects to the coil positive terminal, black connects to the coil negative terminal. clinder select loops figure 3 adjusting the rev limiter. street fire ? www.street-fire.com ? (915) 857-5200 ? fax (915) 857-3344
4 installation instructions harness pn 8876 - dual connector coil. harness pn 8877 - 1996-on gm vehicles. gm ignitions wiring with an msd wiring harness. gray to tach www. street-fire.com pn 5520 cd i m ulti-spa rk igniti o n ? small red white magnetic pickup not used note: see figure 2 for common magnetic pickups. gray to tach www. street-fire.com pn 5520 cd i m ulti-spa rk igniti o n ? white (not used) orange black small red distributor with magnetic pickup msd systems installing to an msd distributor. gm ignitions wiring a dual connector coil. gray to tach www. street-fire.com pn 5520 cd i m ulti-spa rk igniti o n ? small red orange black white both pinks red red note: cut and splice the two pink wires (coil positive) together and connect to orange wire of the ignition. cut and splice the two white wires (coil negative) together and connect to the white of the ignition. if the vehicle is not equipped with a factory tach, there will only be one white wire. note: for a direct plug-in, use msd harness pn 8876. street fire ? www.street-fire.com ? (915) 857-5200 ? fax (915) 857-3344
installation instructions 5 gm ignitions wiring an hei 4-pin module (magnetic pickup trigger). gray to tach www. street-fire.com pn 5520 cd i m ulti-spa rk igniti o n ? small red note: the gm ignition module is removed and replaced with the supplied pn 8861 wire harness. gm ignitions gm large cap hei distributors there are three different large cap hei distributors. to identify which of the following diagrams ft your specifc application, remove the distributor cap and rotor and locate the ignition module at the base of the distributor. count the number of terminals on both ends of the module and follow the corresponding diagram. gm used 4, 5 and 7-pin modules in these distributors. note: some 5-pin models may experience a hesitation or stall on deceleration. if this occurs, contact msd tech line for the required bolt-in diode to correct the problem. msd tech line (915) 855-7123. street fire ? www.street-fire.com ? (915) 857-5200 ? fax (915) 857-3344
6 installation instructions ford ignitions wiring a ford duraspark using white wire trigger. coil gray to tach www. street-fire.com pn 5520 cd i multi-spark igniti o n ? small red magnetic pickup not used gm ignitions wiring an hei 5 or 7-pin module (amplifer trigger). gray to tach www. street-fire.com pn 5520 cd i multi-spark igniti o n ? magnetic pickup not used note: some 5-pin models may experience a hesitation or stall on deceleration. if this occurs, contact msd tech line for the required bolt-in diode to correct the problem. msd tech line (915) 855-7123. street fire ? www.street-fire.com ? (915) 857-5200 ? fax (915) 857-3344
installation instructions 7 magnetic pickup connector pn 8860 harness blac k orange whit e (not used) cover w/t ape + ford distributor violet orange violet black (not used) distributor connector- disconnect from original harness green indica tes connection + + + c+ ta ch not used coil gray to tach www. street-fire.com pn 5520 cd i m ulti-spa rk igniti o n ? small red ford ignitions wiring a ford duraspark using magnetic pickup trigger. ford ignitions wiring a ford tfi with harness, pn 8874. gray to tach www. street-fire.com pn 5520 cd i m ulti-spa rk igniti o n ? small red white magnetic pickup not used ford ignitions wiring a ford tfi (without harness). gray to tach www. street-fire.com pn 5520 cd i m ulti-spa rk igni tion ? small red oran ge white black magnetic pickup not used note: use msd harness, pn 8874. street fire ? www.street-fire.com ? (915) 857-5200 ? fax (915) 857-3344
8 installation instructions chrysler ignitions wiring a chrysler electronic ignition using magnetic pickup trigger. coil gray to tach www. street-fire.com pn 5520 cd i m ulti-spa rk igniti o n ? red orange black magnetic pickup connector white (not used) aftermarket components wiring to a pertronix ignitor kit. distributor with pertronix black coil gray to tach www. street-fire.com pn 5520 cd i m ulti-spa rk igniti o n ? small red magnetic pickup not used msd systems installing to an msd distributor pn 8360. gray to tach www. street-fire.com pn 5520 cd i m ulti-spa rk igniti o n ? sm all red magnetic pickup not used note: the ignition module of the pn 8360 still triggers the street fire ignition. street fire ? www.street-fire.com ? (915) 857-5200 ? fax (915) 857-3344
installation instructions 9 troubleshooting every street fire ignition undergoes numerous quality control checks including a four hour burn-in test. if you experience a problem with your ignition, our research has shown that the majority of problems are due to improper installation or poor connections. the troubleshooting section has several checks and tests you can perform to ensure proper installation and operation of the street fire ignition. if you have any questions, call our customer support department at (915) 855-7123, 7 - 6 mountain time. tach/fuel adapters if your tachometer does not operate correctly or if you experience a no-run situation with your foreign vehicle you probably need a tach adapter from msd ignition. the chart below lists common tachometers and if an adapter is necessary. tachometer compatibility list a ftermarket tachometer white wire trigger magnetic trigger connector autogage 8910 8920 autometer none none ford motorsports none none mallory none none moroso none none stewart (voltage triggered) 8910 8920 s.w. & bi torx none none sun 8910 8920 vdo 8910 8920 amc (jeep) 8910 8920 chrysler 8910 8920 ford (voltage triggered) 8910 8920 general motors bypass in-line filter bypass in-line flter imports 8910 8920 toyota 8910eis note: on the list above, the trigger wire on tachometers that are marked none may be connected to the tach output wire on the street fire ignition. aftermarket components wiring a mallory unilite or 9000 series using points trigger. coil gray to tach www. street-fire.com pn 5520 cd i multi-spark igniti o n ? magnetic pickup not used street fire ? www.street-fire.com ? (915) 857-5200 ? fax (915) 857-3344
10 installation instructions engine run-on if your engine continues to run even when the ignition is turned off you are experiencing engine run-on. this usually only occurs on older vehicles with an external voltage regulator. because the cdi receives power directly from the battery, it does not require much current to keep the unit energized. if you are experiencing run-on, it is due to a small amount of voltage going through the charging lamp indicator and feeding the small red wire even if the key is turned off. early ford and gm: to solve the run-on problem, a diode is supplied in the parts bag. by installing this diode in-line of the wire that goes to the charging indicator, the voltage is kept from entering the cdi. figure 5 shows the proper installation for early ford and gm vehicles. note : diodes are used to allow voltage to fow only one way. make sure the diode is installed facing the proper direction (as shown in figure 5). ford: install the diode in-line to the wire going to the #1 terminal. gm: install the diode in-line to the wire going to terminal #4. gm 1973 - 1983 with delcotron alternators gm delcotron alternators use an internal voltage regulator. install the diode in-line on the smallest wire exiting the alternator (figure 5). it is usually a brown wire. led the led on the side of the street fire monitors several operating conditions of the ignition. if the led indicates that there is a problem with the ignition system, follow the steps through the troubleshooting section. the led will appear to be on steady at above idle speeds when everything is functioning properly. ? when 12 volts are applied to the small red wire, the led will turn on to indicate power. ? when cranking or running, the led will blink for each trigger signal. ? if the input voltage drops below 9 volts it will fash at idle speed. ? code 2 will fash for low battery voltage. ? code 3 will fash for converter off (ignition problem) no-run on foreign vehicles some foreign vehicles with fuel injection systems may require an msd tach/fuel injection adapter to run with the street fire ignition. this is because many of these systems use the same trigger source to operate the cdi, the tachometer and the fuel injection. this results in a voltage signal that is too low to accurately trigger the fuel injection. to fx this, an msd tach adapter, pn 8910, will remedy the problem on the majority of vehicles. if the pn 8910 does not fx the problem, the pn 8910-eis will be required. note: toyotas and ford probes will require the pn 8910-eis adapter. inoperative tachometers if your tachometer fails to operate with the cdi installed you may need a tach adapter from msd ignition. before getting an adapter, try connecting your tachometer trigger wire to the gray wire. this output produces a 12 volt, square wave (see page 1). if the tach still does not operate, you will need a tach adapter. there are two tach adapters: pn 8920: if you are using the magnetic pickup connector (green and violet wires) to trigger the cdi, you will need the pn 8920. pn 8910: if your tachometer was triggered from the coil negative terminal (voltage trigger) and you are using the white wire to trigger the cdi you will need the pn 8910. ballast resistor if you have a current trigger tach (originally coil positive) and use the white wire of the cdi, you can purchase a chrysler dual ballast resistor (used from 1973 - 1976) and wire it as shown in figure 4. from point s or amplifier street fire white street fire red switched 12v (original coil+ wire from tach) chrysler dual ballast resisto r figure 4 wiring the dual ballast resistor. street fire ? www.street-fire.com ? (915) 857-5200 ? fax (915) 857-3344
installation instructions 11 1a-400v diode to charging light splice here or delcotron al terna tor ford vehicles at t ach diode to terminal "1" earl y gm vehicles at ta ch diode to terminal "4" 1 2 3 4 smaller of the 2-wires diode wire loom gm 2-wire al terna tors figure 5 installing the diode to fx run-on. most other applications: on other applications where engine run-on is experienced, a resistor can be put in-line to the street fire's small red wire (figure 6). this resistor will keep voltage from leaking through to the street fire unit. street fire figure 6 wiring the dual ballast resistor for run-on. misses and intermittent problems experience at the races has shown that if your engine is experiencing a miss or hesitation at higher rpm, it is usually not directly ignition. most probable causes include a coil or plug wire failure, arcing from the cap or boot plug to ground or spark ionization inside the cap. several items to inspect are: ? always inspect the plug wires at the cap and at the plug for a tight connection and visually inspect for cuts, abrasions or burns. ? inspect the primary coil wire connections. because the street fire is a capacitive discharge ignition and it receives a direct 12 volt source from the battery, there will not be any voltage at the coil positive (+) terminal even with the key turned on. during cranking or while the engine is running, very high voltage will be present and no test equipment should be connected. warning: do not touch the coil terminals during cranking or while the engine is running. ? make sure that the battery is fully charged and the connections are clean and tight. if you are not running an alternator this is an imperative check. if the battery voltage falls below 10 volts during a race, the cdi output voltage will drop. ? is the engine running lean? inspect the spark plugs and complete fuel system. ? inspect all wiring connections for corrosion or damage. remember to always use proper connections followed by soldering and seal the connections completely. if everything checks positive, use the following procedure to test the ignition for spark. msd also offers an ignition tester, pn 8998. this tool allows you to check your complete ignition system while it is in the car as well as the operation of rpm limits, activated switches and shift lights. street fire ? www.street-fire.com ? (915) 857-5200 ? fax (915) 857-3344
checking for spark if triggering the ignition with the white wire: 1 make sure the ignition switch is in the "off" position. 2. remove the coil wire from the distributor cap and set the terminal approximately 1/2" from ground. 3. disconnect the white wire from the distributor's points or ignition amplifer. 4. turn the ignition to the on position. do not crank the engine. 5. tap the white wire to ground several times. each time you pull the wire from ground, a spark should jump from the coil wire to ground (the led should also blink). if spark is present, the ignition is working properly. if there is no spark skip to step 6. if triggering with the magnetic pickup: 1. make sure the ignition switch is in the "off" position. 2. remove the coil wire from the distributor cap and set the terminal approximately 1/2" from ground. 3. disconnect the magnetic pickup wires from the distributor. 4. turn the ignition to the on position. do not crank the engine. 5. with a small jumper wire, short the magnetic pickup green and violet wires together several times. each time you break this short, a spark should jump from the coil wire to ground (the led should also blink). if spark is present, the ignition is working properly. if there is no spark skip to step 6. 6. if there is no spark: a. inspect all of the wiring. b. substitute another coil and repeat the test. if there is now spark, the coil is at fault. c. if there is still no spark, check to make sure there is 12 volts on the small red wire from the street fire ignition when the key is in the on position. if 12 volts is not present, fnd another switched 12 volt source and repeat the test. d. if, after following the test procedures and inspecting all of the wiring, there is still no spark, the street fire ignition is in need of repair. see the warranty and service section for information. limited warranty m sd warrants this product to be free from defects in material and workmanship under its intended normal use*, when properly installed and purchased from an authorized msd dealer, for a period of one year from the date of the original purchase. this warranty is void for any products purchased through auction websites. if found to be defective as mentioned above, it will be repaired or replaced at th e option of msd. any item that is covered under this warranty will be returned free of charge using ground shipping methods. this shall constitute the sole remedy of the purchaser and the sole liability of msd. to the extent permitted by law, the foregoing is exclusive and in lieu of all other warranties or representation whether expressed or implied, including any implied warranty of merchantability or ftness. in no event shall msd or its suppliers be liable for special or consequential damages. *intended normal use means that this item is being used as was originally intended and for the original application as sold by msd. any modifcations to this item or if it is used on an application other than what msd markets the product, the warranty will be void. it is the sole responsibility of the customer to determine that this item will work for the application they are intending. msd will acce pt no liability for custom applications. street fire ? www.msdignition.com ? (915) 857-5200 ? fax (915) 857-3344 ? 2013 msd llc frm29635 revised 12/13 printed in u.s.a. figure 7 checking for spark with the white wire. www .street-fire.com pn 5520 cd i multi-s p ark igni tion ? white wire trigger www .street-fire.com pn 5520 cd i multi-s p ark igni tion ? violet green jumper wire magnetic pickup trigger figure 8 checking for spark with magnetic pickup. service in case of malfunction, this msd component will be repaired free of charge according to the terms of the warranty. when returning msd components for warranty service, proof of purchase must be supplied for verifcation. after the warranty period has expired, repair service is based on a minimum and maximum fee. all returns must have a return material authorization (rma) number issued to them before being returned. to obtain an rma number please contact msd customer service at 1 (888) msd-7859 or visit our website at www.msdperformance.com/rma to automatically obtain a number and shipping information. when returning the unit for repair, leave all wires at the length in which you have them installed. be sure to include a detailed account of any problems experienced, and what components and accessories are installed on the vehicle. the repaired unit will be returned as soon as possible using ground shipping methods (ground shipping is covered by warranty). for more information, call msd at (915) 855-7123. msd technicians are available from 7:00 a.m. to 5:00 p.m. monday - friday (mountain time).

▲Up To Search▲

Price & Availability of 5520

	To Download 5520 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .